![fuzhou rockchip safe fuzhou rockchip safe](http://www.sipac.gov.cn/english/categoryreport/IndustriesAndEnterprises/202005/W020200520634131686298.jpg)
Rockchip: rk3066: add clock driver for rk3066 soc Rockchip: rk3066: add Rikomagic MK808 boardĭoc: rockchip: add px30/rk3326 boards and examplesĭoc: rockchip: add rk3066 Rikomagic MK808 Rockchip: tools: add rk3066 support to rkcommon.c Rockchip: rk3066-power: sync power domain dt-binding header from LinuxĪrm: dts: rockchip: fix rk3xxx-u-boot.dtsiĪrm: dts: rockchip: fix include rk3xxx-u-boot.dtsiĪrm: dts: rockchip: add rk3066a-mk808.dts
![fuzhou rockchip safe fuzhou rockchip safe](https://i2.wp.com/i0.sinaimg.cn/IT/digi/mp3/2011-11-04/1320358901_38gP5D.jpg)
Sudo dd if=u-boot-dtb.img of=/dev/sda seek=16384 Program commands (SD CARD with GPT partition): Make sure boot and esp flag are set for boot partition.Īppend root=LABEL=linuxroot init=/sbin/init rootfstype=ext4 rootwait Partition Map for MMC device 0 - Partition Type: EFI tools/boot_merger -verbose config-flash.ini With a needle while reconnecting to the USB OTG port to a PC.īus 001 Device 004: ID 2207:300a Fuzhou Rockchip Electronics Company RK3066 in Mask ROM mode If bricked and no BootROM mode shows up then connect pin 8 and 9 of the NAND flash Size of SPL and TPL must be aligned to 2kb.
![fuzhou rockchip safe fuzhou rockchip safe](http://www.hzhaichao.com/images/ezzgyr.jpg)
#Fuzhou rockchip safe full#
U-boot: read Linux kernel from SD CARD.Īdditionally the rk3066 requires everything the BootROM loads to beīoot solution with full U-boot stored on SD CARD:ĪRCH=arm CROSS_COMPILE=arm-linux-gnueabihf- make mk808_defconfigĪRCH=arm CROSS_COMPILE=arm-linux-gnueabihf- make menuconfigĪRCH=arm CROSS_COMPILE=arm-linux-gnueabihf- make all SPL: init SDMMC and read U-boot from SD CARD. With CONFIG_TPL_ROCKCHIP_EARLYRETURN_TO_BROM=y this first stage is combined withįor rk3066 with NAND flash and U-boot this gives the following stages: It always enters at offset 0x804 after a 4 ASCII character "RK30" header.
![fuzhou rockchip safe fuzhou rockchip safe](https://secutechthailand.tw.messefrankfurt.com/content/dam/messefrankfurt-redaktion/secutech_thailand/2020_files/zj_online_products/taizhou_jixing/KS103.jpg)
Then the remainder to offset 0xc00 in the SRAM. Image in two steps: first 1KB to offset 0x800 in the SRAM and Similar to the already supported rk3188, the BootROM will attempt to load up the first stage Of that 64k size only 32kb sram - 2kb bootrom is available for the first stage. The size of a full U-boot binary is too large for the internal SDRAM memory. Unlike later SoC models the rk3066 BootROM doesn't have SDMMC support. If all boot options fail then enter into BootROM mode on the USB OTG port. Supported system boot from the following devices:
#Fuzhou rockchip safe code#
It also includes on-board NANDīoot procedure flow for a Rockchip rk3066 SoC:ġ.Read 2K SDRAM initialization image code to internal SRAMĢ.Run image code to do SDRAM initialization MK808 is a RK3066-based board with 1 USB host and 1 USB OTG port, To: kever.yang +Cc: sjg, philipp.tomsich, lukma, seanga2, u-boot ` (15 more replies) 0 siblings, 16 replies 22+ messages in thread 1:29 ` rockchip: rk3066-power: sync power domain dt-binding header from Linux Johan Jonker Add Rikomagic MK808 board All of help / color / mirror / Atom feed * Add Rikomagic MK808 board 1:29 Johan Jonker